- #Xentry das serial port how to#
- #Xentry das serial port install#
- #Xentry das serial port pro#
- #Xentry das serial port software#
Vediamo V5.00.5 Leave a commentĬome across “Error 23, though reading from H:\1.To start with Put in.exe” when install Super MB Star C3 software, first install on Windows XP laptop, then change another laptop running windows 7, but the problem stays the same. If you have MB SD C4 connect multiplexer, you have to choose Vediamo V5.00.5 to project Benz ECU programming function. After succeed install software, run it and follow the system instructions. IF HAVE ANY PROBLEMS: Copy “Vediamo (Program files)” to C:\Program files\ and rename to Vediamo. Extract DATA archyve and Copy “VediamoData” and “VediamoShortTestData” to C:\ĥ. Copy “Vediamo” from installed folder to C:\Documents and Settings\All Users\ApplicationĤ. Change PIC12F509 in the MB Star C3 Multiplexer (it is not exactly the same as the one in C3 multiplexer, but fit perfectly)ģ.
#Xentry das serial port pro#
MB Star C3 multiplexer (Lowest price MB Star C3, best quality MB Star C3, MB Star C3 Pro with seven cable and Super MB Star C3)ġ. Vediamo 4.2 + PIC12F509 (for MB Star C3 multiplexer ONLY) To program Mercedes Benz ECU and project more powerful function of MB Star C3 DAS and XENTRY, you need a helper: Vediamo 4.2
#Xentry das serial port how to#
How to activate Super MB Star C3 diagnostic software? super mb star c3 Leave a comment If you still have doubts about the problem, please contact mbstarshop customer service. If you remove/reset COM in VMware, back to the default setting or test the COM1 and COM2 separately with COM2. Otherwise the computer will not communicate with Star diagnostic tool. Set your Host PC COM to COM1 before installing the Star diagnostic software.ĭo not remove/set the COM in VMware.
#Xentry das serial port software#
If you have the ability to clone the external hard disk in the VM that also contains the Star Diagnostic software, re-activate the software follow correction instruction. Somehow it does recognize that the multiplexer is attached to Com 1 of the host PC.Įach Super MB Star C3 diagnostic system comes with only one USB dongle, which can fit only one computer.
Unfortunately, the result of CSEAR test is “No device detected”.Īs soon as I rebooted the VM, it reverts to recognizing two Com ports (Com 1 and Com2). I connected the red wire to 12 V DC, amp that I got from one of the power supplies of the host PC that can be used to run an internal hard drive, and connected the black wire to ground (host PC’s chassis.)Ĩ. I connected the multiplexer’s one end to the serial port of the host PC, and for the other, I used the cable that comes with 4 wires at one of its end. Note that the VM takes information from Com 1 of host PC.ħ. As suggested, I removed Port 1, and set Port 2 with speed of 19200 baud rate (see below pix)Ħ. While the host PC has only one port (Com 1), the VM shows two serial ports.
I had to renew Xentry’s key, because it stated that the host has different ID (as some of you had correctly stated, it indeed record’s computer’s physical address) I had to renew it by obtaining a new key from the vendor. I tested the serial port of the host desktop by connecting a thermocouple and recording data through that port.Ĥ. I cloned the external hard drive the VM that also contains the Super MB Star C3 2011.08V Diagnostic software, so to get the software reacting a bit faster.ģ. I used a desktop PC with dedicated serial port (so no need any more to use the Express card that is supposed to simulate a serial port for laptops).Ģ. The problem is a bit long but easy to understand. MBSTARTOOL received an email from one of the customer who explaining his problem in very detail yesterday.
0 kommentar(er)
